| |
About Conn-Weld |
|
Profile Screen Information |
|
Vibrator Panels |
|
Centrifuge Screens |
|
Sieve Bends |
|
Vibrating Screens |
|
Paper Mill Pressure Screens |
|
Contact Conn-Weld |
|
Site Map |
|
Home |
|
| |
|
| Sieve
Bends for the Process Industry <<<<Previous
Page |
| Chart for Determining Open Areas |
 |
Example:
If you desire 1/2mm opening
with C 3/32 wire, the chart will show you that this
would be 18.2% open area. To determine this percentage,
read down the Conn-Weld column at left to 1/2mm.
(or .020 inches) then read straight across to the "C" profile
section under "A" dimension for 3/32. |
|
|
| Opening |
Microns |
Open
Area Percentages |
Opening |
Ref.
Tyler
Mesh |
| Conn-Weld |
"A" Dim. |
Conn-Weld |
| Millimeter |
Inches |
.030 |
.045 |
1/16 |
3/32 |
1/8 |
Millimeter |
Inches |
| - |
.001 |
25 |
3.23 |
2.17 |
1.6 |
1.1 |
0.8 |
- |
.001 |
400 |
| - |
.002 |
50 |
6.25 |
4.26 |
3.2 |
2.2 |
1.6 |
- |
.002 |
250 |
| - |
.003 |
75 |
9.09 |
6.25 |
4.8 |
3.2 |
2.4 |
- |
.003 |
200 |
| - |
.004 |
100 |
11.75 |
8.16 |
6.2 |
4.3 |
3.2 |
- |
.004 |
150 |
| 1/8 |
.005 |
125 |
14.29 |
10.00 |
7.7 |
5.3 |
4.0 |
1/8 |
.005 |
100 |
| - |
.006 |
150 |
16.67 |
11.76 |
9.1 |
6.3 |
4.8 |
- |
.006 |
80 |
| - |
.007 |
177 |
18.92 |
13.46 |
10.4 |
7.2 |
5.5 |
- |
.007 |
65 |
| 1/5 |
.008 |
200 |
21.05 |
15.09 |
11.8 |
8.2 |
6.2 |
1/5 |
.008 |
60 |
| - |
.009 |
229 |
23.08 |
16.67 |
13.04 |
9.09 |
6.98 |
- |
.009 |
- |
| 1/4 |
.010 |
250 |
25.00 |
18.18 |
14.3 |
10.0 |
7.7 |
1/4 |
.010 |
48 |
| 1/3 |
.013 |
330 |
30.23 |
22.41 |
17.8 |
12.6 |
9.8 |
1/3 |
.013 |
42 |
| - |
.015 |
381 |
33.33 |
25.00 |
20.0 |
14.29 |
11.11 |
- |
.015 |
- |
| 2/5 |
.016 |
400 |
34.78 |
26.23 |
21.1 |
15.1 |
11.8 |
2/5 |
.016 |
35 |
| - |
.018 |
450 |
37.50 |
28.57 |
23.1 |
16.7 |
13.0 |
- |
.018 |
32 |
| 1/2 |
.020 |
500 |
40.00 |
30.77 |
25.0 |
18.2 |
14.3 |
1/2 |
.020 |
28 |
| 3/5 |
.024 |
620 |
44.44 |
34.78 |
28.6 |
21.1 |
16.7 |
3/5 |
.124 |
24 |
| - |
.025 |
635 |
45.00 |
35.71 |
29.41 |
21.74 |
17.24 |
- |
.025 |
- |
| 3/4 |
.030 |
750 |
50.00 |
40.00 |
33.33 |
25.00 |
20.00 |
3/4 |
.030 |
20 |
| 1 |
.040 |
1000 |
57.14 |
47.06 |
40.00 |
30.8 |
25.00 |
1 |
.040 |
16 |
| 1-1/4 |
.050 |
1250 |
62.50 |
52.63 |
45.5 |
35.7 |
29.4 |
1-1/4 |
.050 |
14 |
| 1-3/8 |
.055 |
1410 |
64.71 |
55.00 |
47.8 |
37.9 |
31.4 |
1-3/8 |
.055 |
12 |
| 1-1/2 |
.060 |
1500 |
66.67 |
57.14 |
50.0 |
40.0 |
33.3 |
1-1/2 |
.060 |
10 |
| 1-5/8 |
.065 |
- |
68.42 |
59.09 |
52.0 |
41.9 |
35.1 |
1-5/8 |
.065 |
9 |
| 1-3/4 |
.070 |
- |
70.00 |
60.87 |
53.8 |
43.8 |
36.8 |
1-3/4 |
.070 |
8 |
| 2 |
.080 |
- |
72.73 |
64.00 |
57.1 |
47.1 |
40.0 |
2 |
.080 |
7 |
|
| |
| Click HERE for
Sieve Advantages |
Click HERE for
Determining Open Areas |
Click HERE for
Dewatering Capacity |
|
| |
|
